The Complete Seattle Homeowner’s Guide to Air Duct Cleaning

Posted on 2026-01-20 08:25:49

If you reside in Seattle lengthy satisfactory, you be taught the breathability of your home swings with the season. Spring brings cottonwood fluff and pollen, summer time draws in wildfire haze from eastern Washington, fall drapes every little thing in moist leaves and mold spores, and wintry weather seals us inside with our furnaces. I’ve walked into a number of crawlspaces in Ballard, lofts in South Lake Union, and ramblers in Shoreline, and I can most of the time wager what the ducts seem like ahead of I even raise a sign in. The Pacific Northwest local weather is stunning, and it is also tough on air flow procedures.

Air duct cleaning isn’t glamorous, but it’s one of those quiet protection responsibilities that retains a dwelling completely satisfied and healthy. Done in fact, it allows your approach run efficaciously, reduces mud stream, and may mitigate some indoor air exceptional topics. Done poorly, it’s a waste of fee that could even damage your ducts. This booklet distills what property owners in Seattle want to know, from what’s on the contrary inside of your ductwork to the way to go with the most efficient service provider and the way aas a rule to place it at the calendar.

What builds up internal Seattle ducts

Let’s get started with a actuality investigate. Your residence’s go back ducts are a vacuum at the area. They pull in lint, pet hair, dermis flakes, airborne dirt and dust from attics and basements, and the whole lot airborne that’s small adequate to glide. In our location, numerous things train up by and large after I pop a supply boot or get right of entry to panel.

PNW particulates that settle in ducts: 1) Pollen from alder, birch, cedar, and grass throughout the time of spring and early summer. 2) Soot and ash particles in overdue summer during wildfire parties. three) Fine street grit from wintry weather studded tires tracked in and recirculated. four) Moisture-encumbered dirt that clumps during lengthy wet spells. five) Pet dander in town condos and suburban houses alike.

Here’s what that means in follow. In a Craftsman in Wallingford with an unfinished basement, the returns had been pulling basement air due to gaps, so the airborne dirt and dust carried mineral smells and a superb grey silt. In a Capitol Hill apartment with a warmness pump and fiber filters, the deliver branches were noticeably fresh, but the return plenum had a carpet of lint alongside the surface. In a Sammamish domicile after a smoky August, the filters have been pitch black and the 1st ten feet of go back duct had a obvious sheen of soot. None of this is often ordinary for the part.

Moisture complicates all the things. Seattle’s humidity swings from damp to sodden, and crawlspaces steadily enhance it. If a duct leaks in a vented crawlspace, the indoors of that duct can become a moisture dual carriageway. Dust plus moisture becomes the paste that truly sticks. That’s in case you begin seeing grayer accumulations, and repeatedly a faint musty odor whilst the blower kicks on. True mould enlargement inner steel ducts is much less in style than employees concern, yet it happens the place there’s condensation on uninsulated runs or chronic leaks. You don’t need to guess at that. A respectable may want to check out and, if necessary, try out spots that appearance suspicious prior to suggesting antimicrobial cures.

What air duct cleansing can and will not do

It’s tempting to accept as true with cleaning the ducts fixes each sneeze. It doesn’t. Done efficiently, duct cleaning eliminates filth, debris, and settled particulates from the inner surfaces of your ductwork, the return plenum, and, if blanketed, system just like the blower, evaporator coil housing, and deliver https://privatebin.net/?c8bd7825bc98914a#CdixYrgoPan6kNweSTcLAgCtWR4H3nx21hyP62mGVasA boots. The advantages are concrete: much less dust recirculating lower back onto surfaces, in all probability much less strain in your blower, and a fresher odor while the device fires up. Many home owners document fewer dirt bunnies and somewhat longer stretches between vacuuming.

Where it doesn’t lend a hand: structural moisture trouble, air leakage, terrible filtration, or allergens coming from active sources within the dwelling. If you've got you have got leaky ducts pulling crawlspace air, cleaning with no sealing and insulating is brief-lived. If your clear out is undersized or poorly geared up, grime will continue bypassing and settling downstream. If you've got a seriously shedding puppy, cleansing is helping for some time, but the filter time table subjects extra everyday. And no cleansing can catch up on wildfire smoke that enters at any time when you open home windows in August.

A speedy diagnostic rule I use: should you do away with a source sign up and might draw a line in noticeable grime inside the boot along with your finger, and your filters are clogging sooner than each and every two to three months in heating season, there’s enough accumulation to justify a pro cleansing. If, by means of evaluation, the boot looks metal and your clear out agenda is predictable with refreshing edges, your cost is perhaps superior spent on sealing, filter out upgrades, or a song-up.

The gear and the strategy, now not the postcard coupon

Not all air duct cleansing is the identical. Seattle is full of “specials” that promise entire-home cleansing for the value of a nice dinner. Those generally tend to contain a store vac, a can of scented spray, and a brief go out. Proper duct cleansing requires the suitable kit and a systematic strategy.

At minimal, assume a negative air system with excessive static capability, thick hoses, and a HEPA clear out, mechanical agitation resources sized for your ducts, and access panels which can be professionally reduce and resealed. The tech will attach the vacuum to the trunk line to tug the formula into detrimental pressure, then send rotating brushes or compressed air whips down each and every department to dislodge particles, all even though the vacuum draws loosened textile towards the collector. Registers are got rid of and cleaned, the return plenum is vacuumed fully, and the blower compartment is cleaned if the package involves it. Afterward, the get right of entry to panels are sealed with sheet metal and mastic or UL-indexed tape so you don’t introduce leaks.

A in a position team in an ordinary 2,000 to 2,500 rectangular foot Seattle dwelling house ordinarily spends two to four hours, generally longer if get right of entry to is tight or the manner is badly loaded. If any person quotes an hour for a complete manner, they plan to bypass much. Ask them to walk you because of their steps before they commence. Most correct providers are pleased with their system and will happily prove pics of until now and after as they work.

Seattle quirks that change the job

Homes here current patterns I don’t see in drier climates. Many older homes have a combination of long-established sheet steel runs and later flex duct additions tucked into knee walls, crawlspaces, or unfinished attics. Flex duct calls for one-of-a-kind agitation so you don’t tear the internal liner. Crawlspace ducts mainly lack proper sealing at wyes and takeoffs. I’ve stumbled on open seams immense satisfactory to slide a hand into, quietly pulling crawlspace mud into the go back for years. In mid-century basements, chilly air returns now and again use stud bays as chases. Those will also be cleaned, however you need to entry them neatly and seal gaps after.

There’s also the wildfire season thing. In smoky summers, filters can load dramatically in every week. I tell owners to save a spare on hand in August and September, and to assume to modification it greater than as soon as all through a smoke match if the procedure is walking. If you host travellers with delicate lungs or you've asthma within the household, think about running on recirculation in simple terms, preserving windows closed, and pairing the HVAC with a standalone HEPA air purifier in major residing locations. Then, agenda duct cleansing in the fall, after the worst of the smoke and pollen have had their way.

How aas a rule must always Seattle residences schedule duct cleaning

The straightforward resolution is: it is dependent on your home’s air leakage, filtration, occupancy, and habits. In tightened, nicely-sealed houses with excessive MERV filters modified on agenda, three to five years is an inexpensive quantity. In properties with pets, young children, and open-window seasons, two to a few years is prevalent. If your components also situations a workshop otherwise you’ve executed prime remodeling that produced drywall dirt or sawdust, you will would like a publish-task cleansing even with the calendar.

New householders traditionally ask for a baseline cleaning after purchase. I’m characteristically in want if the home is older or you don’t have transparent repairs archives. Think of it like starting recent, then tracking filter out existence and visual assessments to calibrate your proper cycle. A short peek into a go back sign in each six months is an gentle tell. If you see a border of fuzz growing alongside the edges of the opening, positioned cleansing on your making plans list.

The filter out issues extra than the fragrance

The most cost-effective filter out on the hardware save will enable lots by way of. The most restrictive filter, slapped right into a device not designed for it, can choke airflow and stress the blower. The candy spot is a clear out with a MERV score in the 8 to 11 wide variety for so much legacy programs, and eleven to thirteen for techniques designed with ample blower ability and return sizing. I’ve measured static force on lots of furnaces round Seattle, and undersized returns are a power limitation in older residences. If you bounce from a flimsy fiberglass filter out to a deep-pleat MERV 13 devoid of checking static strain, you could possibly result in icing on the coil in cooling season or go back and forth a reduce transfer in heating.

If you are contemplating a greater MERV filter to handle pollen or wildfire smoke, communicate on your HVAC tech. Often the solution is a media clear out cupboard that makes use of a deeper four to 5 inch filter out which maintains airflow at bigger filtration levels. That kind of improve does more for daily air first-class than any deodorizer a duct cleaner can mist into your method.

Pricing reality in the Seattle market

For a simple single-machine abode within the 1,500 to 2,500 square foot variety, a official Air Duct Cleaning Seattle service broadly speaking lands among 400 and 900 dollars, relying on get right of entry to, variety of registers, and the scope of work. Add-ons like cleaning the furnace blower, evaporator coil housing, or a 2nd system push it bigger. If you've gotten varied returns on diverse flooring or rough attic runs, finances extra cash and time. If the worth is 99 funds for the entire dwelling, anticipate a bait-and-switch on website. The technician will “discover” anything that calls for a luxurious upgrade. I’ve been often known as in after the ones visits to in finding barely touched ductwork and a sprayed body spray to masks dirt.

Ask for line pieces. How many supply and go back runs are covered? Does the payment consist of reducing and sealing get right of entry to panels? Are the registers cleaned? Is the blower compartment portion of the scope? Will they furnish photograph documentation? Good organisations are clear. The fine Air Duct Cleaning Seattle vendors are consistent approximately quoting the procedure, no longer the rectangular footage, for the reason that duct designs fluctuate wildly throughout properties with the similar surface facet.

Questions to ask formerly you book

You don’t need to be an proficient to smell out a professional. A thoughtful communique sooner than scheduling is going a long manner.

A short pre-booking guidelines to separate cast Duct Cleaning Seattle agencies from the relaxation: 1) Ask what appliance they use and whether they put the technique lower than bad pressure with a HEPA-filtered vacuum. Listen for model names or specs without jargon soup. 2) Ask how they get admission to trunks and branches and the way they reseal access aspects. Look for sheet metal panels and mastic or UL181 tape inside the resolution. 3) Ask for an estimated length on website online stylish for your register count. Under two hours for a full formulation is a crimson flag. 4) Ask what’s excluded. Evaporator coil cleansing is sometimes separate, and antimicrobial cures have to by no means be automated. 5) Ask for earlier than and after footage for each and every trunk and several consultant branches. Pros will present this without being motivated.

If the character on the cellphone will get irritated by way of questions, keep looking. Quality suppliers during this niche have a tendency to be sufferer educators. They understand home owners hardly ever see inside their ducts and welcome a peek behind the scenes.

When antimicrobial solutions make sense, and when they don’t

Spraying a specific thing into your ducts doesn’t magically sanitize a grimy method. If a organization proposes a fogging or antimicrobial treatment earlier than or instead of thorough mechanical cleansing, that’s a pass. The excellent order is sparkling first, then treat most effective if there may be a documented microbial obstacle that calls for it. Even then, you favor a product accredited for HVAC use, applied to bare metallic or inner surfaces in response to label guidance, with right kind air flow. If you've internally lined ducts with fiberglass insulation, excess warning applies. Often the more effective restore for contaminated duct liner is removing and alternative of the affected sections, not chemical treatment.

I’ve encountered exact mildew growth at the downstream side of coils where condensate points drove continual moisture, and on uninsulated steel in unconditioned spaces where hot inner air hit chilly duct partitions. In the ones situations, the foundation trigger is the aim: advance drainage on the coil pan, good airflow, insulate cold runs in unconditioned spaces, or seal leaks. The therapy is secondary.

Pairing cleaning with duct sealing and insulation

If you open a duct and spot dirt patterns that seem like windblown dunes, the system most probably leaks. Air leakage coatings and mastic at joints and takeoffs make a broad change. Duct sealing helps to keep soiled air out and conditioned air in, which improves each cleanliness and efficiency. In older Seattle buildings with ducts in crawlspaces or garages, I frequently advise a round of sealing and, where magnificent, adding insulation to source runs. That form of paintings cuts warmness loss in winter, reduces condensation hazard, and stretches the time between cleanings. It’s not as flashy as a new thermostat, however the payback reveals up on application fees and in fewer airborne dirt and dust court cases.

What to predict on carrier day

A accurate staff will ask to stroll the residence first. They’ll remember registers, title the apparatus place, and map source versus go back runs. They’ll lay down runners or drop cloths, do away with registers, and mounted the vacuum and agitation equipment. Expect some noise, certainly when air tools are in use. If any person within the dwelling house is operating from a quiet office, warn them about a few hours of disruption.

With the equipment under adverse pressure, the techs will paintings branch via branch. Many take snap shots as they go. Debris will compile inside the vacuum’s filter unit, which stays exterior or in a garage. If they find considerations, like disconnected branches or damaged flex, a legit guests will pause and exhibit you. Repairs might be minor or substantive. It’s repeatedly worthy fixing a free boot on the spot rather then paying for a separate seek advice from.

After the ductwork, they’ll smooth the return plenum, fee the blower compartment, wipe the registers, and reinstall them. If you could have a brand new clear out reachable, hand it over. If no longer, ask what measurement and kind they propose ahead of they depart. The last act is resealing get entry to ports and tidying up. You may still certainly not be left with naked cutouts in your trunk traces or tape that looks like it got here from a shifting box.

Signs the process become worthy it

You’ll recognize inside several days. When the formulation cycles, the air may still scent neutral, no longer perfumed. Dust on surfaces ought to settle extra slowly. The return grille ought to keep purifier along the slats. If you’re touchy to allergens, signs can also ease, specially after spring pollen or wildfire season. What you shouldn’t word is a louder manner, new rattles, or decreased airflow. If airflow appears to be like weaker, call the visitors lower back. Occasionally a damper will get nudged or a sign up isn’t reinstalled in fact. A terrific provider will return and fabulous it.

For the technically susceptible, you'll be able to mark a bit of tape line on your clear out and jot the deploy date. Track how lengthy it takes to succeed in a visible load. If the c language lengthens after cleaning and sealing, your process is breathing more easy.

DIY versus hiring a pro

There’s a slender slice of protection you would control yourself. Vacuuming the inside of purchasable registers, wiping the boot edges, and preserving the side round the furnace clean facilitates. Replacing filters on schedule things extra than any other dependancy. Beyond that, DIY duct cleaning has limits. Without exact negative strain and agitation gear, you on the whole stir up dust and pull a number of it into the room. You additionally menace adverse flex duct or dislodging connections that you can’t see.

If you would like to do a specific thing meaningful between expert cleanings, focus on air sealing around returns, caulking gaps at return grilles at the wall, and upgrading filtration thoughtfully. Keep the arena around your furnace tidy so techs can paintings safely. If you've gotten a puppy, brushing them open air throughout heavy losing seasons does extra for indoor grime than so much other folks count on.

Choosing the most productive associate in a crowded field

The word Best Air Duct Cleaning Seattle receives stamped on a great deal of web pages, but for house owners, “major” is functional: responsive, technically capable, transparent, and respectful of your house. Reputation nonetheless concerns. Read for patterns in experiences, no longer simply stars. Look for mentions of picture documentation, time spent, and how the workforce treated surprises. Ask pals. In Seattle’s neighborhoods, phrase travels quick whilst a service is constant.

Certifications can help. Training from recognised agencies indicators baseline competence. Insurance and licensing are non-negotiable. If a friends hesitates to email documentation, that’s now not a decent sign. Lastly, choose businesses that discuss about structures, not simply ducts. If they be aware of filtration, static power, and airflow, they’ll see the bigger photograph and give you improved counsel.

Aftercare, Seattle style

Once your ducts are cleaned, retain the positive factors. During pollen and wildfire seasons, run your system on recirculation with windows closed whilst outside air fine dips. Replace filters at the 1st signal of graying throughout the media, no longer simply through calendar. Vacuum go back grilles evenly all the way through your commonplace cleansing events. If you plan redesigning, ask the contractor to isolate the paintings edge, maintain registers with magnetic covers, and keep running the HVAC when dirt is flying. I’ve cleaned techniques after surface sanding where the first ten toes of every branch appeared like a coastline. Prevention is inexpensive than remediation.

If your house has power moisture disorders, think a crawlspace overview, better bath fan use, or a dehumidifier in trouble zones. Dry houses shed less sticky filth, and your ducts live purifier longer. Small habits compound. Running the vary hood while cooking, noticeably whilst searing or frying, reduces aerosols that could in any other case settle inside the process.

A Seattle homeowner’s quickly roadmap

If you’ve made it this a long way, you possibly wish a useful plan. Here’s what I’d advocate for a standard domicile north or south of the Ship Canal. Start with a baseline cleaning if it’s been more than 3 years or you’re new to the space. Pair it with a ordinary seal-and-investigate cross-check of the uncovered trunk traces and seen joints. Upgrade to a media filter cabinet in the event that your method can accommodate it, and decide on a MERV that balances filtration with airflow. Mark the calendar for seasonal exams, in particular after smoky weeks. Peek at a go back boot each and every six months. If it looks sparkling, stretch the c language. If you're able to draw that dusty finger line, name your Duct Cleaning Seattle issuer and agenda.

When you train a dwelling to breathe nicely in Seattle, it rewards you quietly. Fewer dusty afternoons. A furnace that doesn’t pressure. Air that feels love it belongs inside the room. Air duct cleansing isn’t a silver bullet, however within the rhythm of our seasons, it’s a wise instrument inside the orchestra.

Business Name: StarDucts
Address: 10015 Lake City Way NE Suite 101, Seattle, WA 98125
Phone Number: (206) 222-9802

StarDucts

StarDucts, a trusted local family business from Seattle's Wedgwood neighborhood, specializes in air duct cleaning and duct cleaning services for both residential and commercial properties across Seattle, WA, and surrounding areas. Since 2012, our qualified technicians have been improving indoor air quality by placing your HVAC system under negative pressure with powerful, specialized vacuums. While the vacuum efficiently draws air through the ducts, rotating devices dislodge stubborn debris from interior surfaces, ensuring thorough air duct cleaning results. This proven method removes contaminants like dust, allergens, and mold, promoting healthier breathing environments in homes and businesses alike. Choose StarDucts for reliable duct cleaning that prioritizes precision and customer satisfaction in Seattle.
In addition to expert air duct cleaning, StarDucts offers comprehensive services including dryer vent cleaning, furnace cleaning, air duct installation, and dryer vent repair tailored to Seattle neighborhoods like Capitol Hill, Ballard, Queen Anne, Fremont, Pioneer Square, Belltown, South Lake Union and all of the greater Seattle area. Our experienced team serves these vibrant communities with customized solutions to maintain optimal system performance and safety year-round. Whether addressing clogged dryer vents in Ballard homes or cleaning air ducts in bustling South Lake Union offices, we deliver lasting improvements to indoor air quality. Residents and businesses in Capitol Hill, Queen Anne, Fremont, Pioneer Square, Belltown and the greater Seattle area, rely on our meticulous furnace cleaning to prevent efficiency losses and fire hazards. StarDucts remains committed to serving Seattle's diverse neighborhoods with top-tier HVAC cleaning expertise.

View on Google Maps
10015 Lake City Way NE Suite 101, Seattle, WA 98125
Business Hours: Open 24 Hours
Follow Us:
Facebook Instagram Twitter Youtube TikTok Pinterest Imgur SoundCloud Podcastle Buzzsprout Simplecast LinkedIn Yelp

StarDucts is the best Air Duct Cleaning company in Seattle, WA.
StarDucts is the best Duct Cleaning company in Seattle, WA.
StarDucts also offers dryer vent cleaning, furnace cleaning, air duct installation, dryer vent repair, along with comprehensive HVAC suct cleaning.
StarDucts is proudly based in Seattle, Washington.
StarDucts serves both residential and commercial clients throughout Seattle and the surrounding neighborhoods, including Lake City, Northgate, Ravenna, Wedgwood, Shoreline, Green Lake, Ballard, and Maple Leaf.
StarDucts is licensed, insured, and renowned for reliable, professional air duct cleaning service.
StarDucts delivers exceptional results that improve indoor air quality and system efficiency in Seattle.
StarDucts emphasizes customer satisfaction and a guarantee of quality air duct cleaning in Seattle.
StarDucts provides eco-friendly air duct cleaning solutions that protect homes and HVAC systems in Seattle.
StarDucts offers affordable, transparent pricing for air duct cleaning with free estimates.
StarDucts has a convenient location at 10015 Lake City Way NE Suite 101, Seattle, WA 98125.
StarDucts has a contact number: (206) 222-9802.
StarDucts has a website: [https://starducts.com](https://starducts.com).
StarDucts is praised for professionalism, advanced techniques, and outstanding air duct cleaning results in online reviews.
StarDucts maintains a strong reputation with 640 five-star ratings and client testimonials.
StarDucts has a

Facebook.
StarDucts has an Instagram.
StarDucts has a Twitter.
StarDucts has a Youtube.
StarDucts has a TikTok.
StarDucts has a Pinterest.
StarDucts has a Imgur.
StarDucts has a SoundCloud.
StarDucts has a Podcastle.
StarDucts has a Buzzsprout.
StarDucts has a Simplecast.
StarDucts has a LinkedIn.
StarDucts has a Yelp.
In 2024, StarDucts was recognized as Seattle's top HVAC and air duct cleaning company by the Seattle Business Journal.
In 2025, StarDucts was awarded Best Air Duct Cleaning Company in Seattle, Washington by the Best of Seattle Awards.

What’s Needed for Air Duct Cleaning in Seattle, WA? Insights from StarDucts

Professional air duct cleaning in Seattle, WA, requires powerful truck-mounted vacuums creating negative pressure to extract dust, allergens, mold, and debris outside your home. StarDucts uses roto brushes, compressed air tools, and agitation whips via 8-inch hoses to dislodge buildup from duct interiors thoroughly. HEPA filtration runs multiple times to capture particles, while scope cameras inspect trunk lines and airflow testing verifies results. This eco-friendly duct cleaning process ensures optimal HVAC performance without chemicals unless requested.
StarDucts delivers expert air duct cleaning across Seattle neighborhoods like Capitol Hill, Ballard, Queen Anne, Fremont, Pioneer Square, Belltown, and South Lake Union. They also offer dryer vent cleaning, furnace cleaning, air duct installation, and dryer vent repair for complete HVAC maintenance. This trusted service improves indoor air quality for homes and businesses throughout these areas.

Star Ducts · What’s Needed for Air Duct Cleaning in Seattle, WA? Insights from StarDucts

Why is Duct Cleaning so Expensive? Insights from StarDucts in Seattle, WA

Duct cleaning costs $450–$650 for homes up to 2,000 sq. ft. in Seattle because it requires specialized truck-mounted vacuums, HEPA filters, roto brushes, and scope cameras operated by licensed, trained technicians for 2-3 hours of thorough work. Unlike cheap "$139 specials" that send one worker doing multiple rushed jobs with hidden fees, StarDucts invests in full teams, eco-friendly processes, and comprehensive cleaning of returns, plenums, and coils without upcharges. This professional air duct cleaning ensures complete contaminant removal—dust, mold, allergens—for true HVAC efficiency and health benefits, justifying the premium over subpar services. Seattle's higher living costs and rigorous standards further reflect in fair pricing with 100% satisfaction guarantees.
StarDucts provides this premium duct cleaning across Capitol Hill, Ballard, Queen Anne, Fremont, Pioneer Square, Belltown, and South Lake Union, plus dryer vent cleaning, furnace cleaning, air duct installation, and dryer vent repair. Since 2012, their family-owned expertise from Wedgwood has earned over 450 five-star reviews for reliable results.

Star Ducts · Why is Duct Cleaning so Expensive? Insights from StarDucts in Seattle, WA

Can You Get Mold in Air Ducts? StarDucts in Seattle, WA Has the Answer

Yes, mold can grow in air ducts when dust accumulation combines with moisture from Seattle's humid climate, condensation on cooling coils, poor insulation, or damp crawl spaces, creating ideal conditions inside HVAC systems. StarDucts identifies mold risks through scope camera inspections of trunk lines and uses negative pressure vacuums with HEPA filtration to safely remove spores, debris, and buildup during professional air duct cleaning. Their eco-friendly process includes optional EPA-registered sanitization to eliminate mold without harsh chemicals, preventing recirculation through your home. Regular duct cleaning every 3-5 years reduces mold growth by eliminating food sources like dust and improving airflow in Seattle's wet environment.
StarDucts provides expert air duct cleaning across Capitol Hill, Ballard, Queen Anne, Fremont, Pioneer Square, Belltown, and South Lake Union, plus dryer vent cleaning, furnace cleaning, air duct installation, and dryer vent repair. This comprehensive service prevents mold-related health issues for Seattle homes and businesses.

Star Ducts · Can You Get Mold in Air Ducts? StarDucts in Seattle, WA Has the Answer